Effect of Various Canopy Shapes on the Drag Coefficient of Pickup Trucks

Khairil Anwar, Muhammad Syaiful Fadly, Muhammad Wahyu Hermanto

Abstract


The aerodynamic performance of light commercial vehicles, such as the Suzuki Carry, plays a crucial role in their fuel economy and road stability. One typical add-on, a canopy, often changes that airflow and, as a result, alters the drag acting on the vehicle. In this study, three different canopy shapes, flat, curved, and triangular, were examined to understand how each one affects the drag coefficient (Cd). To investigate this, both wind tunnel trials and CFD runs were conducted to track the airflow and measure any changes in drag with greater detail. For reference, the exact vehicle without a canopy was used as the base for comparison. From what has been observed, it is clear that adding a canopy tends to increase drag compared to leaving the cargo bed open. Of the three shapes tested, the flat canopy proved to be the most effective in increasing Cd, especially at moderate speeds. At around 80 km/h, for example, it pushed drag up by just over 11.063%. On the other hand, the curved canopy yielded the best result, adding only about 2.071% at 60 km/h. Flow images from the CFD runs showed that the flat and triangular designs disrupted the airflow more significantly, resulting in greater flow separation and larger wakes behind the truck. In contrast, the curved canopy seemed to keep the air closer to the surface, leaving less turbulence in its wake.

Keywords


Canopy, CFD, drag coefficient, pickup trucks, wind tunnel.

Full Text:

PDF

References


C. Bayindirli, Y.E. Akansu, and M.S. Salman, “Drag reduction of truck and trailer combination with different passive flow control methods,” J. Therm. Sci. Technol. Bilim. ve Tek. Derg., vol. 44, no. 2, 2024, doi: 10.47480/isibted.1515727.

C.-C. Wang and C.-P. Wen, “Aerodynamic drag reduction for a truck model using DBD plasma actuators,” Adv. Mech. Eng., vol. 14, no. 3, p. 168, 2022, doi: 10.1177/168781322210878.

B. Basara, Z. Zunic, Z. Pavlovic, P. Sampl, A. Jemcov, W. Edelbauer, S. Saric, and U. Cvelbar, “Performance analysis of immersed boundary method for predicting external car aerodynamics,” SAE Technical Paper, 2022. doi: 10.4271/2022-01-0889.

I.T. Ince, H. Mercan, and N. Onur, “Experimental and numerical analysis of flow over a pickup truck,” Heat Transf. Res., vol. 52, no. 17, 2021, doi: 10.1615/HeatTransRes.2021038655.

A.A. Alshqirate, D.Z. Ghafoor, and S.L. Borse, “CFD analysis of flow over pickup truck with and without covering cargo area using OpenFOAM,” J. Adv. Res. Fluid Mech. Therm. Sci., vol. 90, no. 1, pp. 40–51, 2022, doi: 10.37934/arfmts.90.1.4051.

A.M. Al-Garni, L.P. Bernal, and B. Khalighi, “Experimental investigation of the near wake of a pick-up truck,” SAE technical paper, 2003, doi: 10.4271/2003-01-0651.

P. Mukda, “Effect from accessories on pickup aerodynamics by computational fluid dynamics,” in 6th Int’l Conference on Advances in Engineering Sciences and Applied Mathematics (ICAESAM’2016), 2016, pp. 59–63, doi: 10.15242/IIE.E1216022.

A. Ait Moussa, J. Fischer, and R. Yadav, “Aerodynamic drag reduction for a generic truck using geometrically optimized rear cabin bumps,” J. Eng., vol. 2015, no. 1, p. 789475, 2015, doi: 10.1155/2015/789475.

A.A. Markina, A.D. Lukashuk, S.N. Chepkasov, and A.V Starovoytenko, “Improving aerodynamic characteristics for drag reduction of heavy truck,” in IOP Conference Series: Materials Science and Engineering, 2020, vol. 862, no. 3, p. 32032, doi: 10.1088/1757-899X/862/3/032032.

J. Kim, J. Pattermann, V. Menon, and W. Mokhtar, “A CFD study of pickup truck aerodynamics,” in Proceedings of the 2011 ASEE North Central & Illinois-Indiana Section Conference, 2011.

H. Chowdhury, B. Loganathan, I. Mustary, H. Moria, and F. Alam, “Effect of various deflectors on drag reduction for trucks,” Energy Procedia, vol. 110, pp. 561–566, 2017, doi: 10.1016/j.egypro.2017.03.185.

R. Lietz, L. Larson, P. Bachant, J. Goldstein, R. Silveira, M. Shademan, P. Ireland, and K. Mooney, “An extensive validation of an open source based solution for automobile external aerodynamics,” SAE Technical Paper, 2017, doi: 10.4271/2017-01-1524.

A.R. Paul, A. Jain, and F. Alam, “Drag reduction of a passenger car using flow control techniques,” Int. J. Automot. Technol., vol. 20, pp. 397–410, 2019, doi: 10.1007/s12239-019-0039-2.

M. Hanifudin, G. Jatisukamto, M. Darsin, M.N. Kustanto, A. Saleh, S. Prasetyono, and C.S. Sarwono, “Investigation of drag force and downforce on two racing motorcycles in slipstream conditions,” J. Mech. Eng. Sci. Technol.(JMEST)., vol. 9, no. 1, pp. 52–61, 2025, doi: 10.17977/um016v9i12025052.

F.F. Buscariolo and R.T. Terra, “Ground height and pitch angle influence on the aerodynamic behavior of a production pickup truck,” SAE Technical Paper, 2024, doi: 10.4271/2024-36-0011.

I.A. Ghani, R. Hassan, I. Amin, A. Suhan, K. Husni, D.H. Didane, and B. Manshoor, “Computational fluid dynamics (CFD) study on the aerodynamic of truck,” J. Des. Sustain. Environ., vol. 5, no. 2, pp. 23–27, 2023. https://www.jdse.fazpublishing.com/index.php/jdse/article/view/51

L. Fázecas, N. Avedissian, R. Ghiro, and T. Sonoda, “Improving fuel efficiency for trucks through CFD simulation,” SAE Technical Paper, 2021, doi: 10.4271/2020-36-0410.

E. Wotango, R.B. Nallamothu, S. Kebede, N. Bekele, A.K. Nallamothu, and S.K. Nallamothu, “CFD analysis on aerodynamic drag reduction of pickup vehicles using rear spoiler,” in Advances in Fluid and Thermal Engineering: Select Proceedings of FLAME 2020, 2021, pp. 619–628, doi: 10.1007/978-981-16-0159-0_54.

B. Song, C. Yuan, F. Permenter, N. Arechiga, and F. Ahmed, “Surrogate modeling of car drag coefficient with depth and normal renderings,” in International Design Engineering Technical Conferences and Computers and Information in Engineering Conference, 2023, doi:10.48550/arXiv.2306.06110

R.D.R. Mariaprakasam, S. Mat, P.M. Samin, N. Othman, M. Ab Wahid, and M. Said, “Review on flow controls for vehicles aerodynamic drag reduction,” J. Adv. Res. Fluid Mech. Therm. Sci., vol. 101, no. 1, pp. 11–36, 2023, doi: 10.37934/arfmts.101.1.1136.

N. Xavier, “Calculating the aerodynamic drag coefficient of a Toyota Avanza car CAD model using CFD analysis,” in 2023 31st Southern African Universities Power Engineering Conference (SAUPEC), 2023, pp. 1–5, doi: 10.1109/SAUPEC57889.2023.10057807.

M.N.F. Kamal, I.A. Ishak, N. Darlis, D.S.B. Maji, S.L. Sukiman, R. Abd Rashid, and M.A. Azizul, “A review of aerodynamics influence on various car model geometry through CFD techniques,” J. Adv. Res. Fluid Mech. Therm. Sci., vol. 88, no. 1, pp. 109–125, 2021, doi: 10.37934/arfmts.88.1.109125.

A. Backiyaraj, T. Kumaran, M. Parthasarathy, N.M. Nachippan, and P.B. Senthilkumar, “Vehicle aerodynamics and different testing methods,” in Handbook of Research on Aspects and Applications of Incompressible and Compressible Aerodynamics, IGI Global Scientific Publishing, 2022, pp. 388–406, doi: 10.4018/978-1-6684-4230-2.ch018.

A. Chummar and R. Harish, “CFD simulation of laminar free convection flows of nanofluids in a cubical enclosure,” Mater. Today Proc., vol. 51, pp. 1473–1481, 2022, doi: 10.1016/j.matpr.2021.10.105.

S. Ganesan, R. Thiyagarajan, and P.A.K.M. Khan, “Aerodynamic performance assessment on typical SUV car model by on-road surface pressure mapping method,” SAE Technical Paper, 2021, doi: 10.4271/2021-28-0188.

Z. Xia and M. Huang, “Optimizing the aerodynamic efficiency of electric vehicles via streamlined design: A computational fluid dynamics approach.,” Int. J. Heat Technol., vol. 42, no. 3, 2024, doi: 10.18280/ijht.420315.

W. Gao, Z. Deng, and Y. He, “A comparative study of tail air-deflector designs on aerodynamic drag reduction of medium-duty trucks,” Int. J. Veh. Perform., vol. 8, no. 2–3, pp. 316–333, 2022, doi: 10.1504/IJVP.2022.122138.

M. H. Dasar, D. J. Patil, and M. Raviraj, “CFD Simulation of Pickup Van,” Int. J. Eng. Res. Technol., vol. 2, pp. 1995–2004. https://www.ijert.org/research/cfd-simulation-of-pickup-van-IJERTV2IS120775.pdf.

K. Yathiraj and P. Chaithanya, “Aerodynamics investigations and optimization of a simplified pick-up truck with wind tunnel and CFD testing,” 2024, http://hdl.handle.net/20.500.12380/309024.

M.S. Prasath, C. Sasikumar, and G. Sivaraj, “Numerical studies on aerodynamics performance of modified basebleed to reduce fuel consumption in squareback cars,” J. Appl. Fluid Mech., vol. 18, no. 1, pp. 205–221, 2024, doi: 10.47176/jafm.18.1.2701.




DOI: http://dx.doi.org/10.17977/um016v9i12025p203

Refbacks

  • There are currently no refbacks.


Copyright (c) 2025 Journal of Mechanical Engineering Science and Technology (JMEST)

Creative Commons License
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

View My Stats